C254 BRUSHCUTTERSHINDAIWA OWNER’S/OPERATOR’S MANUALWARNING!Minimize the risk of injury to yourself and oth-ers! Read this manual and familiarize yours
10 WARNING! Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa requirements are NOT approved for use
11NEVER smoke or light res near the engine.ALWAYS stop the engine and allow it to cool before refueling. ALWAYS Wipe all spilled fuel and mo
12Make sure the attachment is clear of obstructions!...and pull recoil starter handle upwardHold the unit rmly...OpenAfter engine starts, move choke
13After the engine starts, allow the engine to warm up at idle 2 or 3 minutes before operating the unit.When the Engine Starts...After the engine is
14Your Shindaiwa unit may be equipped with one of several Shindaiwa trimmer head models, each with features for specic applications and/or operationa
15DO NOT CUTUsing a bladeBlade Thrust“Blade thrust” is a sudden sideways or backward motion of the brushcutter. Such motion may occur when the blade j
16Prior to each work day, perform the following:Remove all dirt and debris from the engine, check the cooling ns and air cleaner for clogging, and
17Remove and inspect the pre-lter. 2. If the pre-lter is torn or otherwise damaged, replace it with a new one.Clean the pre-lter with soap and 3. w
18Combustion chamber should be decarbonized, and the valve clearance should be adjusted. It is highly recommended that this is done by a Shindaiwa-t
19Engine Cover ScrewsEngine CoverMuferMufer Gasket Mufer Bolts Spark Arrester Screen Spark Arrester Cover Cover Screws Mufer and spark arrester ma
2The Shindaiwa H4 series of hand-held power equipment is designed and built to deliver superior performance and reliability without compromise to qua
20WARNING!Sharpen only the cutting teeth of a blade. DO NOT alter the contour of the blade in any way.WARNING!Wear protective gloves when handling or
21Long Term StorageRemove the spark plug and pour about 1/4 ounce of 2-cycle mixing oil into the cylinder through the spark plug hole. Slowly pull t
22Troubleshooting GuideVaporlock.Valve adjustment.Engine hot/heat soaked.Low fuel quality.Valve clearance too tight.Valve clearance too loose.Let cool
23ADDITIONAL PROBLEMSPoor acceleration.Clogged air fi lter.Clogged fuel fi lter.Lean fuel/air mixture.Idle speed set too low.Ignition switch turned off.
24ADDITIONAL PROBLEMSPoor acceleration.Clogged air fi lter.Clogged fuel fi lter.Lean fuel/air mixture.Idle speed set too low.Ignition switch turned off.
25SHINDAIWA LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010ECHO, INC’S RESPONSIBILITYECHO Incorporated’s (ECHO, INC
26PURCHASED REPAIR PARTS AND ACCESSORIES• 90-day all applicationsATTENTION ENGINE POWERED PRODUCT OWNERSThis Shindaiwa engine powered product is a qu
27 ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENTFOR ECHO AND SHINDAIWA BRANDSThe Environmental Protection Agency (EPA) and the California Air
28NOTES
29NOTES
3ALWAYS inspect unit before each use. Replace any damaged parts.NEVER run the engine when trans-porting the unit.NEVER run the engine indoors! Make su
30NOTES
31NOTES
Yamabiko Corporation7-2 Suehirocho 1-Chome, Ohme, Tokyo, 198-8760, JapanPhone: 81-428-32-6118 Fax: 81-428-32-6145Copyright© 2010 By Echo, Incorporat
4Be Aware of the Working EnvironmentAvoid long-term operation in very hot or very cold weather.Make sure bystanders or observers outside the 15 meter
5Product DescriptionUsing the illustration as a guide, familiarize yourself with your machine and its various com-ponents. Understanding your machine
6AssemblyPrior to AssemblyBefore assembling, make sure you have all the components required for a complete unit and inspect unit and components for an
7NOTE:The plastic shield is for use with the Nylon Line Head only. Install Metal Shield when using plastic or metal blades.1. Remove plastic threade
84-6 mm(3/16”-1/4”)Throttle Free PlayRemove air cleaner coverAssembly (continued)Adjust throttle trigger free playThe throttle trigger free play shoul
9The unit should now be completely assembled and ready for use with a blade.IMPORTANT!Discard blades that are bent, warped, cracked, broken or damaged
Commentaires sur ces manuels