Shindaiwa 357 Manuel de service télécharger pdf (Page 130)

Section 14 Appendix Torque Values

Q Shindaiwa Inc. 1995

130

300, 300S, 360, 575, 680,

Location* 377, 488 695 577 757 357

Engine Crankcase 61-70 (70-80) 70-80 (80-90) 70-80 (80-90) 61-70 (70-80) 52-69 (60-80)

Cylinder to Crankcase 61-70 (70-80) 70-80 (80-90) 70-80 (80-90) 79-104 (90-120) N/A

Boot/Insulator to Cylinder ** 17-22 (20-25) 17-22 (20-25) 79-104 (90-120) **

Flywheel Nut 104-122 (120-140) 122-140 (140-160) 200-208 (230-240) 200-208 (230-240) 104-122 (122-140)

Muffler Bolt 61-70 (70-80) 70-79 (80-90) 70-79 (80-90) 5 mm: 70-79 (80-90) 61-70 (70-80)

6 mm: 105 (120)

Spark Plug 148-165 (170-190) 148-165 (170-190) 148-165 (170-190) 148-165 (170-190) 148-165 (170-190)

Oil Pump 17-22 (20-25) 17-22 (20-25) 17-22 (20-25) 17-22 (20-25) 17-22 (20-25)

TCI/Spark Coil 35-44 (40-50) 26-30 (30-35) 26-30 (30-35) 26-30 (30-35) N/A

Exciter Coil 35-44 (40-50) 26-44 (30-50) 26-44 (30-50) 26-44 (30-50) N/A

Carburetor (4 mm) 17-25 (20-30) 17-25 (20-30) 17-25 (20-30) 17-25 (20-30) 17-25 (20-30)

Carburetor (5 mm) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40)

Front Handle (5 mm) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40) 25-35 (30-40)

Front Handle (5.5 mm) 25-44 (30-50) 25-44 (30-50) 25-44 (30-50) 25-44 (30-50) 25-44 (30-50)

Pulser Coil N/A 26-44 (30-40) N/A N/A N/A

Values given in inch/pounds and (Kg-cm)

1 inch/pound = 1.152 Kg-cm

1 Kg-cm = 0.868 in. lbs.)

APPENDIX—TORQUE VALUES

*Use Three BondE 1401 to secure Phillips head screws and all other

fasteners 4mm in diameter and smaller. Except for screws pre-coated from

the factory, apply Three BondE 1360 to all muffler and crankcase screws.

**Install with Three BondE 1401 and tighten per “Other Fasteners” (below).

DO NOT OVERTIGHTEN!

All Other Fasteners Socket Head Phillips Head Nut

4 mm 25-39 (30-45) 13-22 (15-25) —

5 mm 43-61 (50-70) 25-35 (30-40) 23-30 (26-35)

6 mm 79-104 (90-120) 35-52 (40-60) —

8 mm — — 90-106 (104-122)

1 2 ... 125 126 127 128 129 130 131 132 133 134 135 136 137 138

Pas de commentaire

Shindaiwa 357 Manuel de service Page 130