Shindaiwa 400 Spécifications Page 1

Owners Manual Welder/Generator DGW400DM-C ISO 9001 CERTIFIED WARNING!CALIFORNIA – Proposition 65 Warning Diesel engine exhaus

Coolant/Water Temperature Monitor Lamp Danger: Injuries To avoid accidental contact with the cooling fan or fan belts, do not operate this equipmen

If the engine oil pressure drops to an unsafe level during operation, the oil pressure monitor lamp will flash, and the engine will automatically shut

(1) Grounding A qualified electrician should ensure grounding connections of 500 ohms or less at the following 3 points. • The earth grounding termi

The Earth Leakage Relay has activated Caution: Electric Shock / Injuries • If the Earth Leakage Circuit Breaker trips, disconnect all loads connecte

7-8 AC Voltage Adjusting Dial This dial is used to adjust AC output voltage when necessary. Voltage Adjust Dial 13 Decrease Increase <C

<Caution> • If the equipment is not level, you cannot obtain an accurate oil level reading. • Do not overfill (above UPPER line) the engine oi

(1) Filling the Sub Tank 1 Remove the sub tank cap. 2 Add coolant to the FULL level. 3 Re-install the cap. Sub Tank (2) Filling the Radiator 1 Re

• To help prevent solid contaminants from entering the fuel system, the fuel fill strainer should always be used. • To help prevent fuel spills, fil

3. The battery acid specific gravity should never be allowed to fall below 1.23. This may be checked by using a hydrometer. Re-charge the battery i

STARTER SWITCH 1-P 3-P SLOW SWITCH Restarting the engine after running out of fuel. This equipment is equipped with an automatic air bleed

1. Introduction Thank you for purchasing this Shindaiwa Sound Attenuated Diesel Engine Powered Welder/Generator. • This manual was created to help e

10. Welding Operation 10-1 Selection – Welding Cable Always use welding cable of sufficient size for the desired welding amperage at the distance fr

Welding Rod Eco (Single) Single Dual Welding Rod 5/64 –3/16 Welding Rod 7/64 –5/16 Welding Rod 5/64 –5/32 Welding Output Terminal A Welding Output

<Caution> • Never turn the output selector switch while welding. Operation of this switch during welding can cause damage to the switch. This

(2) Semi-Automatic Wire Feeder 1. Turn the CV/CC selector switch to CV. 2. Turn the output selector switch to Eco, Single or Dual, according to the

1-Phase 120/240V Output Receptacle Maximum total single phase output from the 120/240 volt single phase receptacle is 4.3 kVA (4.3 kW), 18 amps at 2

Caution: Injuries • Do not plug loads into the receptacles until it has been verified that the load on/off switch is in the off position. <Caut

13. Checks and Maintenance Danger: Electric Shock, Injuries • Before performing any equipment check or maintenance, stop the engine and remove the

26 Check Check Items Startup Check At 50hrs Every 100 hrs Every 200 hrs Every 400 hrs Every 1000 hrs Every 2000 hrs 1 Check /Add Fuel X

1. Oil Change Frequency 27 First Time 50 hours 2nd Time and thereafter Every 100 hours Procedure 1. Remove the oil fill cap. 2. Remov

3. Clean/Change Air Filter Element Frequency Clean 1st at 50 hours and Every 100 hours Thereafter Replace Every 400 hours <Caution> •

2. Safety Guidelines Danger: Suffocation from exhaust fumes • Exhaust fumes from the engine used on this equipment contain many elements that have

6. Reassemble 7. Open the fuel shut off valve and check for leaks. Retainer Ring Fuel Shutoff Valve Open Close 5. Drain Water from Fuel T

4. After draining the water, reinstall the water drain plug. 5. Refill the coolant system with coolant/water to the upper edge of the radiator

31 Follow the guidelines below when performing any troubleshooting. If you cannot rectify the problem by using this troubleshooting guide, contact

Shindaiwa Incorporated 11975 SW Herman Road Tualatin, OR 97062 Phone 503 692-3070 Fax 503 692-6696 www.kwietpower.com

Caution: Explosion • Do not use this equipment or charge the battery if the battery fluid level is lower than the LOWER level mark on the batter

3. Labels Caution, Danger, Warning and Operation Information Labels: Make sure all information labels are undamaged and readable. Immediately

4. Specifications Model DGW400DM - C Generating Method Rotating Field Rated Current (A) 390 @ 60% Duty Cycle, 302 @ 100% Duty Cycle Rated Voltage

6. Parts DC METERS CURRENT ADJ. DIAL A ECO/SINGLE/DUAL 6 WELDING TERMINALS A MONITOR LAMPS STARTER SWITCH FUEL METER REMOTE CONTROL R

7. Equipment 7-1 Eco Welding This equipment incorporates the Eco welding feature that allows welding operations at a reduced speed (2100 rpm) which r

<Caution> • Do not plug the remote control box into any energized AC receptacle. • Do not connect other loads to the circuit that is powering