Shindaiwa C242 Manuel de l'opérateur

SHINDAIWA OWNER’S/OPERATOR’S MANUALC242 BrushcutterX750280460012/14WARNING! Minimize the risk of injury to yourself and others! Read this manual and f

10C242 BrushcutterAssemblyThis unit comes fully assembled with the exception of the handlebar, throttle assembly, debris shield, trimmer head, trimmer

11C242 BrushcutterConnect throttle linkage1. Move Choke Lever (A) to COLD START position (B) to close choke. This prevents dirt from entering the ca

12C242 BrushcutterAssemblyInstall the debris shield assemblyfor use with a trimmer head1. Place shim (J) on debris shield assembly (K) and insert betw

13C242 BrushcutterThe unit should now be completely assembled and ready for use. NOTE: This unit is shipped with Shaft Bolt (A), Bolt Guard (B), Holde

14C242 Brushcutter1. Turn the trimmer over so that the gear case shaft bolt (A) faces UP.2. Lock gear case by inserting a 4 mm hex wrench (F) into loc

15C242 BrushcutterFuelFuel RequirementsGasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain

16C242 BrushcutterFilling the fuel tank1. Place the unit on a at, level surface.2. Clear any dirt or other debris from around the fuel ller cap.3. R

17C242 BrushcutterStarting a cold engineIMPORTANT!Engine ignition is controlled by a two position stop switch mounted on the throttle handle labeled,

18C242 BrushcutterStarting a warm engineNOTE:If cutting attachment moves, readjust carburetor according to “Carburetor Adjustment: Adjusting Engine Id

19C242 BrushcutterStopping the engine 1. ThrottleRelease throttle trigger (L) and allow engine to return to idle before shutting off engine.2. Stop Sw

2C242 BrushcutterIMPORTANT!The operational procedures described in this manual are intended to help you get the most from this unit as well as to prot

20C242 BrushcutterCutting GrassUnits equipped with a trimmer headYour Shindaiwa unit may be equipped with one of several Shindaiwa trimmer head models

21C242 BrushcutterBladesKeep blades sharp and check blade condition frequently. If a blade’s performance changes suddenly, stop the engine and check t

22C242 BrushcutterGeneral MaintenanceIMPORTANT!MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPA

23C242 BrushcutterNOTE:Use only NGK BPM8Y spark plug (BPMR8Y in Canada) otherwise severe engine damage may occur.1. Remove spark plug (G) and check fo

DCAB24C242 Brushcutter50-Hour MaintenanceEvery 50 hours of operation (more frequently in dusty or dirty conditions):1. Remove and clean the engine co

25C242 BrushcutterCarburetor AdjustmentEngine Break-InNew engines must be operated a minimum duration of two tanks of fuel break-in before carburetor

26C242 BrushcutterAdjusting Engine IdleThe engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and mus

27C242 BrushcutterIMPORTANT!When the wear indicators (D) located at the bottom of the Speed-Feed® trimmer head are worn smooth, or if holes appear, re

28C242 BrushcutterSharpening metal bladesKeep blades sharp and check blade condition frequently. If a blade’s performance changes suddenly, stop the e

29C242 BrushcutterStorageLong Term Storage (over 30 Days)Do not store your unit for a prolonged period of time (30 days or longer) without performing

3C242 BrushcutterAttention StatementsThroughout this manual are special “attention statements”.CAUTION!A statement preceded by the word “CAUTION” cont

30C242 BrushcutterTroubleshooting GuideTroubleshooting GuideVaporlock.Engine hot/heat soaked.Low fuel quality.Let cool completely and restart.Refi ll w

31C242 BrushcutterTroubleshooting GuideIs the engine overheating?Engine is rough at all speeds. May also have black smoke and/or unburned fuel at the

32C242 BrushcutterADDITIONAL PROBLEMSPoor acceleration.Clogged air fi lter.Clogged fuel fi lter.Lean fuel/air mixture.Idle speed set too low.Ignition sw

33C242 BrushcutterModel Name C242Length w/o cutter head 1,745 mm (69.1 in.)Width 575 mm (22.6 in.)Height 490 mm (19.3 in.)Weight (dry) w/o cutter head

34C242 BrushcutterWarranty statementsSHINDAIWA LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2013ECHO, INC’S RESPONSIB

35C242 BrushcutterWarranty statementsPURCHASED REPAIR PARTS AND ACCESSORIES• 90-day all applicationsATTENTION ENGINE POWERED PRODUCT OWNERSThis Shind

36C242 BrushcutterNOTES

37C242 BrushcutterThank you for choosing Shindaiwa Power EquipmentPlease go to http://www.shindaiwa-usa.com to register your new product on-line. It&a

38C242 BrushcutterNOTES

39C242 BrushcutterNOTES

4C242 BrushcutterSafety InstructionsPersonal Condition and Safety EquipmentWARNING! Users of this product risk injury to themselves and others if the

40C242 BrushcutterECHO Incorporated.400 Oakwood RoadLake Zurich, IL 60047-1564 U.S.A.Telephone: 1-877-986-7783Fax: 1-847-540-8416www.shindaiwa.comYama

5C242 BrushcutterEquipmentWARNING! Use only ECHO Inc. attachments. Serious injury may result from the use of a non-approved attachment combination. EC

6C242 BrushcutterSafety InstructionsVibration and Cold It is believed that a condition called Raynaud’s Phenomenon, which affects the ngers of certai

7C242 BrushcutterAn Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by engine FAMILY).PRODUCT

8C242 Brushcutter1817192322201524131016111412DescriptionLocate the safety label(s) on your unit. Make sure the label(s) is legible and that you unders

9C242 BrushcutterDescription1 POWER HEAD - Includes the engine, clutch, fuel system, ignition system, intake and exhaust systems and recoil starter.2