Shindaiwa C220 Manuel de l'opérateur télécharger pdf (Page 16)

16

Using a Blade

WARNING!

n Before working with a blade-

equipped unit, always inspect and

clean the area of objects that could

interfere with or damage the blade.

n Never use a blade near sidewalks,

fence posts, buildings or other

objects that could cause injury or

damage.

n Never use a blade for purposes

other than those for which it was

designed.

n Whenever you strike a hard ob-

ject with a blade, always stop the

brushcutter and carefully inspect the

blade for damage. NEVER OPER-

ATE THE BRUSHCUTTER WITH A

DAMAGED BLADE!

n A blade-equipped unit must be

equipped with a bicycle-type handle-

bar or barrier bar as well as a har-

ness or shoulder strap.

n Always make sure the cutting at-

tachment shield is properly installed

before operating this unit.

Blade Thrust

‘Blade thrust’ is a sudden sideways or

backward motion of the brushcutter. Such

motion may occur when the blade jams or

catches on an object such as a sapling tree

or tree stump. BE CONSTANTLY ALERT

FOR BLADE THRUST AND GUARD

AGAINST ITS EFFECTS!

Brushcutter Handlebar

A brushcutter handlebar or barrier bar

helps prevent the operator from moving

forward, or the unit moving rearward, thus

preventing inadvertent bodily contact with

the blade. ALWAYS KEEP THE HANDLE-

BAR OR BARRIER BAR SECURELY IN

PLACE ON THE UNIT!

Make sure to use the following recom-

mended Shindaiwa cutting attachment with

this machine.

(A) T220, C220

PART NUMBER 67000-65010

UN-34-7L

TAP & FEED TRIMMER HEAD

BOLT DIAMETER: 7 mm

THREAD: LEFT, 1.0 mm PITCH

Recommended Cutting Attachment

The blade rotates counter-clockwise. For

best performance and to minimize being

stuck by debris, move the blade from right

to left while advancing on your work.

C220/T220

Position the blade so cuts are made be-

tween the blade’s 8 o’clock and 10 o’clock

positions (as viewed from above). DO NOT

cut between the 10 o’clock and 5 o’clock

positions.

WARNING!

When cutting wood with a saw, feed the

blade slowly—never strike or “slam” a

spinning blade against the wood.

WARNING!

DO NOT use 2-tooth or non-Shindaiwa

approved 4-tooth cutting blades with

Shindaiwa trimmers and brushcutters.

Vertical Cuts

Hold the brushcutter with the blade at a 90

0

angle to the ground so the blade’s bottom

edge rotates toward the operator. Move the

blade from top to bottom through the cut,

and cut only with the bottom edge of the

blade.

WARNING!

When making vertical cuts, never allow

the blade to exceed waist height.

Cut on the left side of

the blade. KEEP YOUR

BODY OUTSIDE

THE PATH OF BLADE

ROTATION

D

O

N

O

T

C

U

T

Ten

O'clock

OK To Cut

Eight

O'clock

Five

O'clock

Blade

Rotation

C220/T220

Brushcutter Shoulder Strap

A shoulder strap provides additional

protection against blade thrust. In addition,

a shoulder strap gives signiﬁcant support

and comfort to help ensure safe and

efﬁcient operation.

When operating a unit with a blade, make

sure both the handle and shoulder strap

are adjusted to the size of the operator us-

ing the unit.

PART NUMBER 60903-98320

4-TOOTH BLADE

INNER BORE: 25.4 mm

DIAMETER: 255.0 mm

THICKNESS: 2.0 mm

PART NUMBER 60903-98310

8-TOOTH BLADE

INNER BORE: 25.4 mm

DIAMETER: 255.0 mm

THICKNESS: 2.0 mm

(B) F220

PART NUMBER 67001-65010

TAP & FEED TRIMMER HEAD

BOLT DIAMETER: 8 mm

THREAD: RIGHT, 1.25 mm PITCH

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 65 66

Commentaires sur ces manuels

Pas de commentaire