Shindaiwa C220 Manuel de l'opérateur Page 9
- Page / 66
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
9
F220
1. Place the cutting attachment shield
under the triangular flange.
2. Tighten 3 screws (16 mm).
NOTE:
The 3 screws (16 mm) are in the tool bag.
Cutting Attachment Shield Assembly
WARNING!
NEVER operate this machine without
the cutting attachment shield. Operating
without the cutting attachment shield may
result in serious injury.
WARNING!
Carefully inspect the cutting attachment
shield assembly to make sure it is tight-
ened securely and does not wobble.
Flange
Cutting
Attachment
Shield
Screw 16 mm
WARNING!
The line cutter is very sharp. Wear
gloves to protect your hands when
handling.
To Change Position of Line Cutter.
1. Remove the 2 hex screws with a 4 mm
hex wrench.
2. Rotate line cutter.
3. Reinstall the two hex screws and tighten
them securely.
NOTE:
Be careful to not lose the 2 nuts in the cutting
attachment shield, they are not captured.
The line cutter can be positioned in
2 positions to obtain different line length
for cutting.
F220
Install the Cutting Attachment
Shield C220/T220.
1. Insert the cutting attachment shield
between the outer tube and the cutting
attachment shield mounting plate.
CAUTION!
Make sure the clamp screw and retain-
ing nut are securely tightened before
tightening the four socket-head cap
screws.
NOTE:
It may be necessary to loosen the retaining
nut and clamp screw to adjust cutting attach-
ment shield mounting plate.
2. Fit the two shims and the bracket over
the outer tube and loosely install the
four socket-head cap screws.
3. Tighten the four socket-head cap screws
to secure the cutting attachment shield.
Sub-Shield.
(when trimmer head is in use)
1. Attach the shield extension to the
cutting attachment shield.
WARNING!
NEVER use this machine without sub-
shield when using a trimmer head.
CAUTION!
Make sure the sub-shield is completely
hooked at the hook receiver.
Sub-shield
Hook
Hook
Receiver
Cutting Attachment Shield
Line Cutter
Hex
Screws
Socket-head
Cap Screws
Shim
Shim
Nut
Bracket
Cutting Attachment Shield
Outer Tube
T220/C220
Cutting Attachment
Shield Mounting
Plate
- F220 GRASS TRIMMER 1
- T220 GRASS TRIMMER 1
- C220 BRUSHCUTTER 1
- Contents 2
- Attention Statements 2
- Introduction 2
- Safety Information 2
- Safety Labels 4
- Unit Description 4
- Specications 5
- Outer Tube Assembly 6
- Assembly of the Handle 6
- Installing a Trimmer Head 10
- Mounting a Blade C220/T220 11
- Filling the Fuel Tank 12
- Mixing Fuel 12
- Starting the Engine 13
- Engine Idle Adjustment 14
- Unit Condition Check 14
- Stopping the Engine 14
- Operation 15
- Standard Shoulder Strap 15
- Using a Blade 16
- Daily Maintenance 17
- 10 Hour Maintenance 17
- 10/15 Hour Maintenance 17
- Maintenance 17
- 50 Hour Maintenance 18
- Mufer Maintenance 19
- Long Term Storage 19
- Blade Sharpening 19
- Troubleshooting Guide 20
- Symptom Possible Cause Remedy 21
- DECLARATION 22
- CONFORMITY 22
- DÉBROUSSAILLEUSES C220 23
- DÉBROUSSAILLEUSES F220 23
- DÉBROUSSAILLEUSES T220 23
- Table des matières 24
- Mises en garde 24
- Informations de sécurité 24
- AVERTISSEMENT ! 25
- PLACER LA POIGNÉE 26
- DEVANT CETTE LIGNE 26
- Caractéristiques techniques 27
- Assemblage du tube extérieur 28
- Poignée T220 29
- Guidon C220 29
- JAM NUTS 30
- GROUND WIRE 30
- IGNITION WIRE 30
- REMARQUE : 32
- Montage d’une lame C220/T220 33
- Remplissage du réservoir 34
- Mélange de carburant 34
- Démarrage du moteur 35
- Arrêt du moteur 36
- Réglage du ralenti du moteur 36
- Contrôle de l’état de 36
- Fonctionnement 37
- Bretelle standard 37
- Utilisation d’une lame 38
- Entretien quotidien 39
- Entretien aux 10 heures 39
- Entretien aux 10 à 15 heures 39
- Entretien 39
- Entretien aux 50 heures 40
- Entretien du silencieux 41
- Remisage à long terme 41
- Affûtage de la lame 41
- Guide de dépannage 42
- Guide de dépannage (suite) 43
- DÉCLARATION 44
- CONFORMITÉ 44
- TAGLIAERBA F220 45
- TAGLIAERBA T220 45
- DECESPUGLIATORE C220 45
- Sommario 46
- Messaggi informativi 46
- Introduzione 46
- Informazioni sulla 46
- Prestare attenzione 47
- Etichette di sicurezza 48
- Descrizione dell’apparecchio 48
- Speciche 49
- Assemblaggio del tubo esterno 50
- Assemblaggio dell’impugnatura 50
- Installazione di una 54
- Clip di 55
- Rifornimento del serbatoio 56
- Miscelazione del carburante 56
- Avviamento del motore 57
- Arresto del motore 58
- Verica delle condizioni 58
- Funzionamento 59
- Tracolla standard 59
- Utilizzo di una lama 60
- Marmitta di scarico 61
- Dispositivi di chiusura 61
- Manutenzione ogni 50 ore 62
- Manutenzione della 63
- Rimessaggio per 63
- Aflatura della lama 63
- Risoluzione dei problemi 64
- Italiano 65
- ULTERIORI PROBLEMI 65
- DICHIARAZIONE 66
- CONFORMITÀ 66
Produits connexes et manuels pour Tondeuses à gazon Shindaiwa C220
(8 pages)
(52 pages)
(92 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.418 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels